How to Calculate Steel Coil Weight and Length: Formulas, Worked Examples, and a Decoiler Sizing Checklist
A coil shows up on the dock with a tag that says one thing and a forklift driver who says another. Before it goes on a decoiler, someone needs to know two numbers: how much it weighs and how much strip is wound on it.
Get the weight wrong and you overload the decoiler. Get the length wrong and you run out of strip halfway through a job. Both problems are easy to avoid with a tape measure, a calculator, and three simple formulas.
This guide walks through the coil weight and coil length formulas, shows two worked examples, and ends with a checklist for picking a decoiler that can handle your coils.
Key Takeaways
A coil is a hollow cylinder of metal. Its weight is the volume of that cylinder times the density of the metal. Its length is the cross-section area divided by the strip thickness. You only need four measurements: outside diameter, inside diameter, width, and thickness. Use the result to pick a decoiler rated above your heaviest coil.
| What You Want | Formula (inches and pounds) | What You Need to Measure |
|---|---|---|
| Coil weight | 0.7854 × (OD² − ID²) × W × density | OD, ID, width, metal type |
| Coil length | 0.7854 × (OD² − ID²) ÷ T ÷ 12 = feet | OD, ID, thickness |
| Length from weight | Weight ÷ (W × T × density) ÷ 12 = feet | Tag weight, width, thickness |
| Pounds per inch of width (PIW) | Weight ÷ W | Coil weight, width |
OD = outside diameter, ID = inside diameter, W = strip width, T = strip thickness, all in inches. 0.7854 is π ÷ 4.
Pallet Decoilers for Heavy Coils
Durant's motorized pallet type uncoilers are offered in models from 500 lbs to 12,000 lbs capacity.
Explore Pallet DecoilersWhy Coil Weight and Length Matter
Coil math is not just for the purchasing office. It affects the whole line.
- Decoiler capacity: Every decoiler has a weight rating. A coil that is too heavy wears out bearings and drives and can be a safety risk.
- Job planning: Knowing the strip length tells you how many parts a coil will make before a changeover.
- Handling: Forklifts, hoists, and coil cars all have limits too.
- Checking deliveries: A quick calculation tells you if the tag weight looks right.
Step 1: Take Four Measurements
- Outside diameter (OD): Measure across the full coil, through the center.
- Inside diameter (ID): Measure across the hole in the middle. Do not assume it from the paperwork.
- Width (W): Measure the strip from edge to edge.
- Thickness (T): Use a micrometer on the strip, not the nominal size on the paperwork.
Heads Up: Keep every measurement in the same unit. If you mix inches and millimeters, the answer will be wrong by a lot.
Step 2: Pick the Right Density
Density is how much a cubic inch of metal weighs. It changes with the metal. The Engineers Edge density table lists these common values:
| Metal | Density (lb/in³) | Density (g/cm³) |
|---|---|---|
| Mild steel | 0.284 | 7.85 |
| Stainless steel | 0.278 to 0.289 | 7.7 to 8.0 |
| Aluminum | 0.098 | 2.70 |
For a specific alloy, use the density on the mill certificate or the supplier's data sheet.
Step 3: Calculate Coil Weight
A coil is a ring of metal. Its volume is the area of the ring times the width. Multiply by density and you have the weight.
Coil weight (lbs) = 0.7854 × (OD² − ID²) × W × density
Worked Example 1: A Heavy Steel Coil
Mild steel coil, 48" OD, 20" ID, 12" wide, 0.060" thick.
- OD² − ID² = 2,304 − 400 = 1,904
- Ring area = 0.7854 × 1,904 = 1,495.4 square inches
- Volume = 1,495.4 × 12 = 17,945 cubic inches
- Weight = 17,945 × 0.284 = about 5,096 lbs
The same size coil in aluminum would weigh about 1,759 lbs. Same coil, very different decoiler.
Step 4: Calculate Coil Length
To find how much strip is on the coil, divide the ring area by the strip thickness. That gives you inches of strip. Divide by 12 for feet.
Coil length (ft) = 0.7854 × (OD² − ID²) ÷ T ÷ 12
Using the coil from Example 1:
- Ring area = 1,495.4 square inches
- 1,495.4 ÷ 0.060 = 24,923 inches
- 24,923 ÷ 12 = about 2,077 feet of strip
Notice that width and density are not in this formula. Length depends only on the diameters and the thickness.
Length From the Tag Weight
If you only have the tag weight, you can work backward:
Coil length (ft) = Weight ÷ (W × T × density) ÷ 12
Check: 5,096 ÷ (12 × 0.060 × 0.284) ÷ 12 = about 2,077 feet. Same answer.
Worked Example 2: A Lighter Coil
Mild steel coil, 30" OD, 20" ID, 6" wide, 0.040" thick.
- OD² − ID² = 900 − 400 = 500
- Ring area = 0.7854 × 500 = 392.7 square inches
- Weight = 392.7 × 6 × 0.284 = about 669 lbs
- Length = 392.7 ÷ 0.040 ÷ 12 = about 818 feet
What Is PIW?
PIW stands for pounds per inch of width. It is the coil weight divided by the strip width. Mills and service centers often quote coils this way because it lets you compare coils of different widths.
- Example 1: 5,096 ÷ 12 = about 425 PIW
- Example 2: 669 ÷ 6 = about 112 PIW
If a supplier quotes PIW, multiply it by your width to get the coil weight.
Know Your Coil Weight? Let's Match the Decoiler.
Send us your coil OD, ID, width, and weight. A Durant specialist will help you choose a decoiler with the right capacity.
Talk to a SpecialistDecoiler Sizing Checklist
Once you know your coil, use it to size the decoiler.
1. Weight Capacity
Size for your heaviest coil, not your average one. Pick a model rated above that weight, not right at it.
2. Coil OD vs. Table or Reel Size
The coil must sit fully on the table or reel. A 48" OD coil needs a table at least that size.
3. Coil ID
Make sure the center hub, arbor, or guide drum fits your coil ID.
4. Strip Width
Check that the guides or drum can handle your widest strip.
5. Line Speed
The decoiler must pay out strip at least as fast as your press or roll former uses it. Match the decoiler RPM range to your line speed and coil size.
6. Floor Space and Loading
Think about how coils get loaded. Pallet type decoilers let you set an entire pallet of coil stock on the table, which can save time and handling.
How the Examples Match Durant Pallet Decoilers
Durant's product page lists motorized pallet type uncoilers in these capacity groups:
| Capacity | Turntable Diameters | RPM Ranges |
|---|---|---|
| 500 lbs (227 kg) | 30", 36" | 0–12, 0–25, 0–50 |
| 1,200 lbs (546 kg) | 30", 36", 42" | 0–12, 0–25, 0–50 |
| 3,500 lbs (1,591 kg) | 42" | 0–12, 0–25, 0–50 |
| 5,000 lbs (2,273 kg) | 42", 48" | 0–12, 0–25, 0–50 |
| 6,000 lbs (2,727 kg) | 48" | 0–12, 0–25, 0–50 |
| 7,500 lbs (3,409 kg) | 52", 60" | 0–12, 0–25, 0–50 |
| 8,500 lbs (3,864 kg) | 60" | 0–12, 0–25 |
| 10,000 lbs (4,546 kg) | 60" | 0–12, 0–25 |
| 12,000 lbs (5,455 kg) | 60" | 0–12, 0–25 |
Specifications from Durant Tool Company's pallet type uncoiler product page. Contact Durant to confirm the right model for your coil and line speed.
Applying the checklist to the two examples:
- Example 1 (about 5,096 lbs, 48" OD): Too heavy for the 5,000 lb models. A 6,000 lb model with a 48" turntable covers both the weight and the diameter.
- Example 2 (about 669 lbs, 30" OD): Over the 500 lb rating. A 1,200 lb model with a 30" or larger turntable fits.
Durant also lists features that matter when you are handling heavy coils, including no turntable pinch points from casters or drive wheels, reverse rotation with the flip of a switch, and placement within 2 feet of the press with no slack loop required. To see how these machines work in more detail, read how pallet type uncoilers work.
Common Mistakes to Avoid
- Using nominal thickness: Measure it. Small thickness errors make big length errors.
- Forgetting the ID: Leaving out the hole in the middle makes the coil look much heavier than it is.
- Using the steel density for every metal: Aluminum weighs about a third as much as steel for the same size.
- Sizing for the average coil: Your heaviest coil is the one that counts.
- Mixing units: Stay in inches and pounds, or millimeters and kilograms, all the way through.
Keep in Mind: These formulas assume a tightly wound coil. A loosely wound coil has air gaps, so its real weight and length will be a little lower than the calculated numbers. Use the tag weight as a cross-check.
Ready to Handle Heavier Coils?
Durant pallet decoilers come with a standard three-year warranty and models up to 12,000 lbs.
Request a QuoteConclusion
Coil weight and length come from the same four measurements: outside diameter, inside diameter, width, and thickness. Add the right density, and you can check a delivery, plan a run, and size a decoiler in a few minutes.
Measure carefully, size for your heaviest coil, and match the decoiler to your coil diameter and line speed. Your equipment will last longer and your jobs will run without surprises.
Have a coil you are not sure about? Reach out to Durant Tool Company for help choosing the right decoiler for your coils.
FAQs
How do you calculate the weight of a steel coil?
Multiply 0.7854 by (OD² − ID²), then by the strip width, then by the density. For mild steel, use 0.284 lb per cubic inch. Keep all measurements in inches.
How do you calculate the length of a coil?
Multiply 0.7854 by (OD² − ID²) and divide by the strip thickness. That gives the length in inches. Divide by 12 for feet.
Can I calculate coil length from the weight?
Yes. Divide the weight by (width × thickness × density). That gives inches of strip. Divide by 12 for feet.
What does PIW mean for steel coils?
PIW means pounds per inch of width. It is the coil weight divided by the strip width.
What density should I use for steel?
Mild steel is commonly listed at 0.284 lb per cubic inch (7.85 g/cm³). For an exact alloy, use the value from the mill certificate.
How do I choose a decoiler capacity?
Calculate the weight of your heaviest coil and choose a decoiler rated above it. Then check that the table or reel fits your coil OD and ID and that the speed matches your line.



