Request a Quote

For A Durant specialist And Lowest Instant Prices

Rotary Indexing Tables Explained: Mechanical Cam vs. Servo Indexers, How They Work, and How to Choose One

Rotary Indexing Tables Explained: Mechanical Cam vs. Servo Indexers, How They Work, and How to Choose One

Rotary Indexing Tables Explained: Mechanical Cam vs. Servo Indexers, How They Work, and How to Choose One

A regular turntable spins. A rotary indexing table stops. That one difference is what makes it useful on a production floor.

An indexing table turns a set amount, stops dead at a station, holds still while work gets done, then moves to the next spot. Load a part, drill it, inspect it, unload it. Or fill one bin with stamped parts, then swing an empty bin into place. Same motion, over and over, in exactly the same spots.

This guide explains how rotary indexers work, how mechanical cam and servo indexers compare, where count-based parts collectors fit in, and what to check before you buy one.

Key Takeaways

A rotary indexing table moves a round top through a fixed number of stations and holds it still at each one. Cam indexers repeat one motion with high rigidity. Servo indexers can be reprogrammed for new angles and timing. Count-based indexers, like parts collectors, move to the next station after a set number of parts. To choose one, start with the number of stations, the load, the table diameter, and what will tell the table when to move.

What to CheckWhy It MattersSimple Rule of Thumb
Number of stationsSets how far the table turns each timeDivide 360 degrees by the stations you need
LoadParts, fixtures, and bins all add weightAdd up the weight when every station is full
Table diameterFixtures or bins must fit with room to spareLay out your stations on paper first
Index triggerSomething has to tell the table when to moveMatch it to a timer, a PLC, or a part count
Index time vs. dwell timeMoving time is lost work timeKeep the move short and the hold long enough
GuardingA moving table creates pinch pointsPlan guards before the table goes on the floor

Indexing Tables Built for the Press Floor

Durant's Parts Collector / Index Tables count stamped parts into containers and index automatically to the next position.

Explore Index Tables

What Is a Rotary Indexing Table?

A rotary indexing table, also called a rotary indexer or dial indexer, is a round table that turns in fixed steps. Each step is called an index. Each stop is called a station.

Every cycle has two parts:

  • Index: The table moves from one station to the next.
  • Dwell: The table holds still so work can happen at each station.

Because every station gets the same treatment, one table can do several jobs at once. While a part is being loaded at station one, another can be assembled at station two and a third inspected at station three.

Indexing Table vs. Continuous Turntable

People mix these up all the time, and they are not the same machine.

FeatureIndexing TableContinuous Turntable
MotionMoves, stops, holds, moves againTurns at a steady speed
StopsFixed stations, same spot every timeNo set stopping points
Typical jobsAssembly, machining, part collection, inspectionStretch wrapping, packing, display, hand work
What you size it byStations, load, and index timingLoad, diameter, and speed

If your operators just need the work to come around to them, a turntable may be enough. If the work has to stop in the same place every time, you need an indexer.

How Does a Rotary Indexer Work?

Every indexer does the same basic job. A drive moves the table one step, then something locks or holds the table while the station works. What changes from one type to another is how that move is created and what tells the table to go.

The step size comes straight from the number of stations:

Index angle = 360 degrees ÷ number of stations. An 8-station table moves 45 degrees per index. A 6-station table moves 60 degrees. A 4-station table moves 90 degrees.

Mechanical Cam Indexers

A cam indexer uses a shaped cam to turn the table. As the cam rotates, its profile pushes followers on the table and moves it one station. The rest of the cam profile holds the table still. That holding section is the dwell.

Because the motion is cut into the cam, a cam indexer does the same move the same way every time. Assembly Magazine's guide to selecting a rotary indexing table notes that cam designs are a common pick for heavy or unbalanced loads during dwell.

Good fit when:

  • The job does not change for a long time
  • The load is heavy or uneven around the table
  • You want a simple, rigid machine

Trade-off: The number of stations and the move profile are built into the hardware. Changing them usually means changing the cam.

Servo Indexers

A servo indexer uses a servo motor and a controller to move the table. The move is set in software, not in a cam. That means you can change the index angle, the speed, and the dwell by changing the program.

Good fit when:

  • You run several part numbers that need different station counts
  • Dwell time changes from job to job
  • The table has to talk closely with robots or a PLC

Trade-off: More controls to set up and support. Heavy, uneven loads need careful sizing and tuning.

Count-Based Indexers: Parts Collectors

Not every indexing job is about assembly. On a press line, the job is often simpler: collect a set number of parts in a bin, then swap in an empty bin without stopping the press.

That is what a parts collector does. Durant describes its Model PC 2000 Parts Collector / Index Table this way: you set a count mechanism to the number of parts you want per container. Once that number is produced, the turntable indexes automatically to the next position.

The trigger here is a part count, not a timer. That makes it a natural partner for a production counter. If you are choosing one, our guide on electronic vs. mechanical counters covers the options.

Durant Parts Collector / Index Table Specifications

Durant's product page lists eight index positions on its standard 36-inch table, with larger tables up to 72 inches available with more than eight positions. Published models cover the following ranges:

CapacityTurntable DiametersExample Models
500 lbs (228 kg)30", 36", 48"PC 530, PC 536, PC 548
1,000 lbs (455 kg)30", 36", 48"PC 1030, PC 1036, PC 1048
2,000 lbs (909 kg)30" to 72"PC 2030 through PC 2072
3,000 lbs (1,365 kg)30" to 72"PC 3030 through PC 3072
5,000 lbs (2,275 kg)36" to 72"PC 5036 through PC 5072

Specifications from Durant Tool Company's parts collector product page. Contact Durant to confirm the right model, number of positions, and count control for your line.

Not Sure Which Indexer Fits Your Line?

Tell us your part, your bin size, and your press speed. A Durant specialist will help you choose the right index table.

Talk to a Specialist

Cam vs. Servo vs. Count-Based: Quick Comparison

TypeWhat Sets the MoveBest ForWatch Out For
Mechanical camCam shapeFixed, repeat jobs and heavy loadsChanging stations means changing hardware
ServoMotor programChanging jobs and automated cellsMore setup and controls work
Count-based parts collectorA set part countBin changes on press and stamping linesCount must match the bin's real capacity

6 Things to Check Before Buying a Rotary Indexing Table

1. How Many Stations Do You Need?

Count every step: load, work, check, unload. Add a spare station if you think the process will grow. Then use the index angle formula to see how far the table moves each time.

2. What Is the Full Load?

Add up the weight of parts, fixtures, and containers with every station full. For a parts collector, that means every bin full of parts at the same time. Pick a table rated above that number.

3. Will Your Fixtures or Bins Fit?

Draw a circle the size of the table and place your stations around it. If bins or fixtures overlap, you need a bigger table or fewer stations.

4. What Tells the Table to Move?

A timer, a PLC signal, a sensor, or a part counter can all start an index. Pick the trigger that matches your process. On a press line, counting parts is often the simplest and most reliable choice.

5. Is the Dwell Long Enough?

The table must hold still long enough for the slowest station to finish. If one station takes twice as long as the others, it sets the pace for the whole table.

6. How Will You Guard It?

A moving table near hands creates pinch points. OSHA's general requirements for all machines (29 CFR 1910.212) call for guarding against hazards like in-going nip points and rotating parts. Plan guards, sensors, or stop controls into your layout from the start.

Heads Up: Never reach onto an indexing table while it can move. Lock out power before clearing jams, changing fixtures, or swapping bins by hand.

Where Indexing Tables Help on a Metalworking Floor

  • Stamping and press lines: Collect a set count of parts per bin without stopping the press.
  • Assembly cells: Move a part past several tools on one compact footprint.
  • Machining and drilling: Load one part while another is being cut.
  • Inspection: Stop each part in front of a gauge or camera in the same spot every time.
  • Packaging: Fill, check, and close containers station by station.

Floor space is often the deciding factor. For a side-by-side look at layouts, see rotary indexer vs. straight belt accumulator. If your job needs fine angular positioning for machining instead, our guide to high precision rotary tables covers that side.

Common Mistakes to Avoid

  • Buying a turntable when you need an indexer: If the work must stop in one spot, a steady-turning table will not do it.
  • Sizing for one full bin, not all of them: Every station can be loaded at once.
  • Forgetting the slowest station: It sets the dwell for the whole table.
  • Setting the part count too high: Overfilled bins spill and slow down the next station.
  • Adding guards as an afterthought: They are easier and cheaper to plan up front.

Ready to Automate Your Bin Changes?

Durant Parts Collector / Index Tables are offered from 500 to 5,000 lb capacity and 30" to 72" diameters.

Request a Quote

Conclusion

A rotary indexing table does one simple thing very well. It moves work to the same spot, holds it still, and repeats. Cam indexers give you a rigid, repeatable move for jobs that do not change. Servo indexers give you a move you can reprogram. Count-based parts collectors keep press lines running by changing bins on their own.

Start with your station count, your full load, and what will tell the table to move. Get those three right, and the rest of the choice gets much easier.

Need help picking an index table for your press or assembly line? Reach out to Durant Tool Company for expert help choosing the right model.

FAQs

What is a rotary indexing table used for?

It moves parts or containers through a fixed set of stations and holds them still at each one. Common uses include assembly, machining, inspection, packaging, and collecting stamped parts into bins.

What is the difference between a rotary indexer and a turntable?

An indexer stops at fixed stations and holds still between moves. A continuous turntable keeps turning at a steady speed with no set stopping points.

How do I work out the index angle?

Divide 360 degrees by the number of stations. An 8-station table indexes 45 degrees per move.

Is a cam indexer or a servo indexer better?

Neither is better for every job. Cam indexers suit fixed, repeat work and heavy loads. Servo indexers suit jobs where the angle, speed, or dwell needs to change.

What is a dial indexer?

Dial indexer is another name for a rotary indexing table. The round top is often called the dial plate.

How does a parts collector know when to index?

Durant's parts collector uses a count setting. You set the number of parts per container, and once that count is reached, the table indexes automatically to the next position.

« Back to the blog

check out button

Product Category